Viper car alarm manual - vlogophracos

Viper Alarm Wire Diagram

The sequence consists of the siren sounding continuously and the parking lights flashing for a pre-programmed period, which can range in duration from 1 to 180 seconds. You can't go wrong.

Install the ignition kill relay, making the appropriate electrical connections. Can someone me a.

Viper 3000 Owner's Manual - How would I program it?

IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. The 2-way remote is powered by a 1. Low Battery Notification If the battery is low and this feature is programmed On the 2- way remote will emit 2 long beeps 5-seconds after a transmission is completed. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesirable operation. Silent Mode works by pressing this button for less than one second before arming or disarming. An optional auxiliary function, such as trunk release, can be controlled by pressing this button for 1. Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. If after 2-seconds the remote beeps once, the Orange LED flashes 6-times and the Red LED lights for 3-seconds, the system has detected an open door, hood or trunk and has been bypassed. The sequence consists of the siren sounding continuously and the parking lights flashing for a pre-programmed period, which can range in duration from 1 to 180 seconds. See the Table of Zones section of this guide. Pressing seconds of arming the security system will activate the Multi- Level Security Arming feature. Once the system is disarmed and then re-armed, all the zones will be active again. After each press of the remote will emit normal arm notification 1 beep and 3 flashes of the Orange LED. Ignition controlled The dome light activates for 30-seconds after the ignition is turned On. If the remote has beeps programmed On, the remote will beep. This is very useful when washing the vehicle or having it serviced. In Valet Mode, the security system will not arm, even with the remote transmitter, but all convenience functions door locks, trunk release, etc. It prevents annoying repetitive trigger sequences due to ® faulty door pin switches or environmental conditions such as thunder, jackhammers, airport noise, etc. Example If the alarm triggers three times within a 60-minute period and each time the same sensor or switch triggers the alarm, NPC interpret those triggers as false alarms. Decrease Sensitivity—Press and release the decrease shock sensor sensitivity by one step. The siren will chirp 1-time for each step decreased in adjustment. When the shock sensor adjustment reaches minimum sensitivity sensor is Off the siren will emit 1 short and then 1 long chirp. The system will emit 3 chirps to indicate the sensor has been reset to level 10. The system returns to shock sensor adjustment mode for further adjustment, if required. Once the light shuts off, however, the doors are monitored normally. If four chirps are heard when disarming, the system was triggered in your absence. Description System armed System armed with Bypass Notification System disarmed System disarmed with Tamper Alert ® System disarmed NPC active... The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. Zone - Number of LED Flashes Description... If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the in- vehicle status LED. Active or triggered zones will be indicated by a pattern of blinks by this LED. The alarm will automatically re-sync and respond to the trans- mitters normally. If the system remains in Valet come back on the next time the ignition is turned on and then back off. This feature only works if passive arming has been programmed. Thirty seconds later, the starter of the vehicle will be disabled. To start the car, it will be necessary to disarm the system with the remote. It is also possible to disarm the AED feature by turning the ignition key to the RUN position and pressing the Valet times. The parking lights will flash and the siren will chirp once. This can be done before driving or while driving the vehicle. From this point on, when the ignition key is turned off, the VRS will immediately turn on the starter kill. This will prevent the vehicle from being restarted, thus immobilizing it at that spot. To disarm the VRS ® 1. Turn the ignition on. Press the Valet button the pre- programmed number of times to disarm the VRS note: If the VRS... If two sensors are triggered the LED will report showing the siren icon and the alarm will sound. After the ignition has been turned off, it will continue to supply power until a door has been open and closed. In addition, the 545T will turn your headlights on whenever the windshield wipers are used. A transmitter function can also be used to turn on your parking and headlights for a programmed time. Usually hidden under Control Unit: the dash area of the vehicle. The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration. When the system arms, you will hear a short siren sound, or chirp, and the parking lights will flash once. Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, Directed is ISO 9001 registered.

The parking lights on the vehicle will quickly go on and off to give you a visual indicator of the lock engaging and the activation of the alarm. Since the system is plugged to your OBD, CarLock gives you a visual feedback to your car battery status and so much more. This time nothings working and as soon as I put the put in, the alarms goes off and there is no way to shut it off. Use your multimeter to find the wires you need. Activate the passive alarm feature of the alarm by simply turning off the vehicle once you've parked, and then by closing the door after leaving the automobile. But sirens blaring in parking lots or across the street have made us almost immune to the sound. The viper alarm and car security system is perfect for those who need a really simple yet feature-packed device to keep their cars secure. Because it can be complicated for the average person, we recommend professional installation. Viper car alarm manual your car alarm unit, run the valet switch, LED lights, and external antenna before connecting everything to the siren. Likewise, if the shock sensor is activated, the system sends an alert to the remote.